Skip to content

Tape measure Body Shape Calculator with Measurements

Type in your shoulders, bust, waist and hips and get your body shape right away, with a score for all five shapes.

Unit

Free, no account. The math runs in your browser; your measurements are never sent to us.

SHOULDERS BUST WAIST HIPS
Measure all the way around, tape level with the floor.

How to measure yourself

Use a soft tape, wear light fitted clothes or underwear, and stand relaxed with your feet together. Keep the tape level all the way round, snug but not pressing in. A mirror or a second person helps with the back.

01

Shoulders

Arms relaxed at your sides. Wrap the tape around both shoulders and upper arms at the widest point, just below the bony tip of the shoulder.

02

Bust

Around the fullest part of your chest, with the tape straight across your back. Wear a bra without padding, or none, and breathe normally.

03

Waist

Around the narrowest part of your torso, usually a little above the navel. Breathe out gently and do not pull your stomach in.

04

Hips

Around the fullest part of your hips and seat, with your feet together. Check it in a mirror from the side; the tape tends to drop at the back.

Measure each one twice. If the two readings differ by more than half an inch (about 1 cm), take a third and use the middle one.

How the calculator decides

It compares the differences between your bust, waist and hip measurements using the FFIT rules (Female Figure Identification Technique), developed at North Carolina State University from 3D body scans and used by Lee et al. in 2007 to compare the body shapes of women in the US and Korea.

A tape measures the distance around your body, not how wide you look from the front. That is why this page does not reuse the width ratios from our photo body shape calculator; it uses circumference rules written for tape measurements instead.

The rules the measurement calculator uses, checked in this order
Shape Rule (inches) Source
Hourglass Bust and hips within 1 in, and waist 9 in or more below the bust or 10 in or more below the hips. Also FFIT's top hourglass (bust 1 to 10 in above hips, waist 9 in or more below bust) and bottom hourglass (hips 3.6 to 10 in above bust, waist 9 in or more below hips). FFIT
Inverted triangle Bust 3.6 in or more above the hips, and waist less than 9 in below the bust. FFIT
Pear Hips 3.6 in or more above the bust, and waist less than 9 in below the hips. FFIT triangle
Apple Waist at least 0.85 times the hips, and less than 9 in below the bust. WHO waist to hip cut point
Rectangle Bust and hips within 3.6 in of each other, waist less than 9 in below the bust and less than 10 in below the hips. FFIT

The first rule that fits wins. If none fits exactly, the shape whose rule you miss by the fewest inches wins. The percentages come from the same distances: the closer you are to a shape's rule, the higher its score, and the five add up to 100.

Shoulders only break ties. FFIT does not use shoulders. When the bust, waist and hip rules say hourglass or rectangle and your shoulders measure at least 1.15 times your hips, the calculator calls you an inverted triangle instead. That 1.15 cut point is our own choice, not a published one.

Where we simplify. FFIT has nine shapes. We fold them into the five shapes used across this site, so top and bottom hourglass both count as hourglass. FFIT separates bottom hourglass from its "spoon" shape with a high hip measurement we do not ask for, so a spoon figure shows up here as hourglass with pear close behind. FFIT's oval and diamond shapes need stomach and abdomen measurements; in their place we use the WHO waist to hip ratio of 0.85, the cut point for central fat in women.

Limits. These rules were built from women's body scans. Men can use the calculator, but more of them will read as rectangle or apple, and the shoulder tie break matters more. A body shape is a description of proportion. It says nothing about size or health, and we do not publish an accuracy figure for it.

References

  1. Simmons, K., Istook, C. L. and Devarajan, P. (2004). Female Figure Identification Technique (FFIT) for apparel, part II: development of shape sorting software. Journal of Textile and Apparel, Technology and Management, 4(1).
  2. Lee, J. Y., Istook, C. L., Nam, Y. J. and Park, S. M. (2007). Comparison of body shape between USA and Korean women. International Journal of Clothing Science and Technology, 19(5), 374 to 391.
  3. World Health Organization (2011). Waist circumference and waist-hip ratio: report of a WHO expert consultation, Geneva, 8 to 11 December 2008.

Questions

What the tape can tell you, and how it compares with a photo.

How do I calculate my body shape from measurements?

Measure around your bust, waist and hips, then compare the differences between them. If your bust and hips are within about an inch of each other and your waist is at least 9 inches smaller than your bust or 10 inches smaller than your hips, you are an hourglass. Hips 3.6 inches or more above your bust point to pear, bust 3.6 inches or more above your hips to inverted triangle, and small differences everywhere to rectangle. This calculator runs those rules for you and adds a score for every shape.

Why does the calculator ask for my shoulders?

Shoulders only matter when the bust, waist and hip rules say hourglass or rectangle. In that case, if your shoulder measurement is at least 1.15 times your hip measurement, the calculator calls you an inverted triangle instead, because a broad shoulder line changes how clothes hang even when bust and hips are close.

Will I get the same result as the photo calculator?

Usually, but not always. A tape measures the distance around your body, while the photo body shape calculator measures how wide your outline is from the front. Someone with a deep but narrow chest, for example, measures larger on a tape than they look in a photo. If the two disagree, read both shape guides; you likely sit between them.

What if I am between two body shapes?

Then both descriptions are useful. The percentage breakdown shows how close each shape is, and a second score near the first means a small change in one measurement would flip the result. Measure again to rule out a slipped tape, then use the styling advice from both guides.

Are my measurements stored?

No. The calculation runs in your browser and your numbers are never sent to us. We only count that the calculator was used and which shape came out, with nothing that identifies you. Details are on the data privacy page.